How to Replace Brake Light Switch 2008 Gmc Sierra

By Ra_Malia579 11 May, 2022 Post a Comment

Electric Hand Brake Switch Button For Chevrolet For Silverado For GMC For Sierra 1500 2500 3500 2008-2011 1S11002 15137492 15839548 15861245 Car Brake Stop Light Switch Handbrake Control Switch. Adjust the switch so that the brake lights activate with a touch of the brake pedal.

50 Best Of Brake Light Wiring Diagram Chevy Chevy Silverado Chevy Chevy Trucks

Show 26 more comments.

. I discovered this because my cruise control wasnt working I had the switch replaced cruise worked but within a short time my brake lights werent turning. Brake light bulbs grow dimmer over time and eventually burn out. Print this page.

The only way to get the clip off is to destoy it. May 27 2017 by terry woods. I believe that the BCM controls the brake light on your truck.

They will only come off or on the shaft in two pieces. To remove the old and before you install the new you have to pop the switches apart. 8 people found this helpful.

The switch has a plunger in it that contacts a lever in the brake pedal assembly. The switch is typically a small plastic box with 2 or 3 wires coming from it. The computer in newer models will use this information.

Switch by unsnapping from pushrod. I found the best tool to use is a Door Upholstery removal tool. Above the brake pedal there will be a small white in color switch with two wires coming out of it.

Im about to have my brake light switch replaced for the 3rd time in less than 1 year. With the brake pedal in the relaxed position no pressure applied to the pedal the contacts of the switch should be mounted up against the pedal stop on the pedal housing. This not only lets other drivers know that your Sierra is slowing down or stopping but the brake light switch on newer Sierras may also send information to the engine computer.

How to Turn off Your Sierras Brake Light. The only way to turn the brake light off is to restore proper line pressure to both brake circuits when the pedal is pushed. It holds the white plastic brake light switch on the rod.

If you mess up fixing your engine the vehicle does not move. The brake light switch is also in the circuit. I had to replace my brake light switch cause when i stepped on the brakes the they would work till i put more pressure on the peddle then they would go outnow i have no brake litesi have flashers an turn signals but no brake lightswhat could it bechecked everything but the bulbs.

Retainer from brake pedal pin. When pressure is applied to the brake pedal as if braking the contacts of the switch close thus closing the circuit and energizing the brake lights. As that plunger is depressed when you push on the brake pedal the contacts in the brake light switch closed and voltage flows to the brake lights turning them on.

Loosen the bolt that holds the cable onto the terminal remove the cable and tuck it somewhere so that it does not make contact with the negative side. When you replace the brake light bulb on your Sierra 1500 be careful not to. The brake light switch is a mechanical switch activated when you press the brake pedal.

1A Auto has a large selection of Brake Stop Lamp Switches for your GMC Sierra 1500 and ground shipping is always free. Just have it towed to a mechanic. Electrical connector from switch.

When you replace the brake light bulb on your Sierra 1500 be careful not to. If your Sierra is having trouble stopping or noticeably leaking fluid dont drive it. Jesse answered 5 years ago Under the bed where the wires attach they can get worn and crack after.

I replaced break light switch and now break lights stay on but dont work properly Posted by John Crispino on Jan 26 2014. Install or Connect Electrical connector into switch. The brake lights on your 2008 GMC Sierra 1500 illuminate when you hit the brake pedal and help prevent you from being rear ended by the cars behind you.

Switch is attached to the pedal Remove or Disconnect Negative battery cable. A bad brake light switch for example can trigger the ABS and traction control lights but it can also prevent engine start or even transmission shifting. 2008 GMC SIERRA.

This video shows you how to change the brake lights on your 2008 GMC Sierra 1500. All connections are good. Switch by snapping it onto pushrod.

This video shows you how to change the brake lights on your 2003 GMC Sierra 1500. I discovered by brake lights do not turn off. The clip is on the passenger side of the rod.

Clicking this will make more experts see the question and we will remind you when it gets answered. If you mess up fixing. Retainer onto brake pedal pin.

The brake lights on your 2003 GMC Sierra 1500 illuminate when you hit the brake pedal and help prevent you from being rear ended by the cars behind you. Visit us online or call 888-844-3393 and order today. The switch signals the controller that the brake pedal is depressed.

Shop for the best Brake Light Switch for your 2008 GMC Sierra 1500 and you can place your order online and pick up for free at your local OReilly Auto Parts. This is the brake switch. You need to look at data stream for BCM and see what the BCM is seeing in relation to the pedal sensor.

Then shop at 1A Auto for a GMC Sierra 1500 Brake Stop Light replacement at a great price. Electronic Parking Hand Brake Car Brake Stop Light Switch For Chevrolet For Silverado For GMC For Sierra 1500 2500 3500 2008-2011 1S11002 15137492 15839548 15861245 Handbrake Control Switch Brake Butt. The job is about 20-25 minutes and you need a 10mm wrench to take off one bolt on a retaining clip.

SLESierra Enthusiast Member 32. However because of the angle it is nearly impossible to get a screwdriver under it. Need to replace a bad Brake Light Switch on your GMC Sierra 1500 as soon as possible.

After replacing the lower intake manifold gasket on my 1997 GMC Sierra the service engine soon light stays on. Add a comment. You will need to pull the pigtail from the brake switch and then unscrew the switch and replace with new one.

Use 11mm 716 inch. Brake light bulbs grow dimmer over time and eventually burn out. How do you replace break light switch in 2008 gmc sierra 1500 k.

F fernando apodaca More information. In this article we go over the symptoms of a bad brake light switch and test them. Brake light switch replacement GMC Sierra step by step instructions U style clip on nuts Follow along as Betty changes out a brake light switch on an 08 GMC Sierra If you watch till somewhere a little past the 5 minute mark.

The brake light switch on your GMC Sierra sometimes called the stoplight switch turns on the brake lights when you step on the brake pedal. To get to the switch take a look right above brake pedal. The brake light switch on modern vehicles is no longer a simple switch used to turn on the brake lights.

Use snap ring pliers. My price was around 1700 but down in the US its probably around 10-12. He clip is on rod that is on the upper part of the brake pedal.

Trailer Brake Controller Information Etrailer Com Tekonsha Trailer Wiring Diagram Electrical Diagram